Skip to content

How to fit kitchen door handles

Handles are the last thing to go on and the easiest thing to get wrong, because a handle drilled in the wrong place cannot be undrilled. This guide covers how to position them, how to drill them, and the jig trick that makes a whole kitchen come out consistent.

Before you drill anything

Three decisions come first, and all three are easier to change now than later.

Bar, knob or cup

Bar handles suit slab and handleless styles and are the easiest to grip. Knobs suit shaker doors and are traditional on anything framed. Cup handles are usually used on drawers, often with knobs on the doors.

Where they go

Convention, not a rule:

  • Base unit doors. Handle near the top, on the opening edge.
  • Wall unit doors. Handle near the bottom, on the opening edge.
  • Drawers. Centred horizontally, and centred vertically on the front.
  • Tall units. Roughly at the height a base unit handle would be.

The logic is that handles end up where your hand already is. It also keeps the handles on a run of base units and the handles on the wall units closer together, which looks calmer than the alternative.

How far in from the edge

Somewhere between 30mm and 60mm from the edge of the door is normal. Pick one number and use it on every door in the kitchen. Consistency reads as quality far more than the exact figure does.

Centres

A bar handle is specified by its centres, the distance between the two fixing holes. Common sizes are 96mm, 128mm, 160mm and 192mm, but handles exist at almost any size, so measure the handle you have bought rather than assuming.

If you are reusing existing holes, measure the centres of those holes and buy a handle to match. It is much easier than filling and redrilling.

Marking out

  1. Work on the back of the door, so any pencil marks that survive are hidden.
  2. Mark the distance in from the edge, and the distance down from the top or up from the bottom.
  3. For a bar handle, mark one hole, then measure the centres across from it and mark the second.
  4. Check the two marks are level with each other. A handle a degree off is visible from across the room.
  5. Mark the centre of each hole with a bradawl or a centre punch so the drill bit cannot wander.

Drilling

Use a sharp bit of the right size, usually 5mm for an M4 handle screw. Two things save you from a chipped face:

Drill from the back. The bit pushes material ahead of it and tears out where it exits. Drilling from the back puts the tear out on the back.

Back the door with scrap. A piece of offcut clamped behind the exit point supports the face as the bit comes through. On a gloss or a lacquered door this is the difference between a clean hole and a repair.

Go slowly, keep the drill square to the face, and do not lean on it.

The jig

If you are doing more than a handful of doors, make a jig. A piece of ply or MDF with your two holes drilled in it and a lip that hooks over the edge of the door. Hook it on, drill through the holes, move to the next door.

Every handle ends up in exactly the same place, you cannot mismeasure, and a whole kitchen takes a fraction of the time. Make one jig for base doors and one for wall doors if the positions differ.

Fitting

Handle screws come in a few lengths because door thicknesses vary. Use the shortest one that goes fully through the handle thread. A screw that bottoms out before it tightens will leave the handle loose, and one that is too long will not pull up at all.

Tighten until firm and then stop. Over tightening a screw into a handle casting strips the thread, and over tightening against a lacquered face can craze the finish around the hole.

If you change your mind later

Handle holes are the one part of a door you cannot undo. If you think you might change handles in a year or two, buying a style with the same centres saves you a set of doors. Going from a 128mm bar to a 160mm bar means new holes and two visible old ones.

Frequently asked questions

Do doors come pre-drilled for handles?

It varies by range and by how the door is supplied. Ring 01206 616626 with the range you are looking at and we will tell you what that one does.

Can I fill old handle holes?

On a painted or wrapped door you can fill and touch in, and it will be visible if you look for it. On a gloss or a woodgrain it will be visible without looking for it. If the new handles do not match the old centres, plan on it showing.

What about handleless doors?

J-pull and true handleless doors have the grip built into the door or into a rail behind it, so there is nothing to drill. That is part of their appeal and part of why they cost more.

Should the handles match the taps?

They do not have to, and in a lot of kitchens they do not. If you want them to, decide it before you buy either, because matching a finish afterwards is harder than it sounds.