Skip to content

How to measure kitchen door hinges

New doors have to work with the hinges in your kitchen, or with hinges you are prepared to buy. This guide covers how to identify what you have, how to measure the hinge positions, and what to check before ordering.

What is almost certainly in your kitchen

If your kitchen was built in the last thirty years or so, it will use concealed hinges, also called European or cup hinges. The hinge has a round cup that sits in a hole bored into the back of the door, and an arm that screws to a mounting plate on the inside of the carcass.

Two measurements describe that hole, and between them they decide whether a hinge will fit a door.

Cup diameter

Almost always 35mm. There are 26mm cups on some slimline and glass door hinges, but on a standard kitchen door, 35mm is the number. Measure across the hole at its widest point.

Boring distance

The distance from the edge of the door to the near edge of the cup hole. Usually between 3mm and 7mm. Measure from the outside edge of the door, square across, to where the hole starts.

Some people measure to the centre of the cup instead. Both are used, so if you are quoting a number to anyone, say which one you measured.

Measuring where the hinges sit

As well as the hole itself, note where up the door the hinges are. For each door:

  1. Measure from the top edge of the door to the centre of the top hinge cup.
  2. Measure from the bottom edge to the centre of the bottom hinge cup.
  3. Count the hinges. Tall doors often have three, very tall ones four.

Write these against the door number on the list you made when you measured the doors themselves. If you are reusing your existing hinges and your new doors will be bored, those positions are what the new holes have to match.

Overlay, and why it matters

Overlay is how far the door covers the carcass side next to it. It is set by the hinge and the mounting plate, not by the door.

Three arrangements exist:

  • Full overlay. The door sits over the full thickness of the carcass side. The common case on an end unit or a single door.
  • Half overlay. Two doors share a carcass side, each covering half of it. Common in the middle of a run.
  • Inset. The door sits inside the frame rather than over it. Unusual in modern kitchens.

You do not normally need to change any of this when you replace doors, because you are keeping the same carcasses and, usually, the same hinges. It matters if you are buying new hinges, because you have to buy the same type you are replacing.

Checking your hinges are worth keeping

Hinges are cheap relative to doors and they are the part that wears. Before you decide to reuse them, open and close a few and look for:

  • A door that drops when you let go of it
  • Visible play in the arm when you wiggle the door
  • A soft close that no longer softly closes
  • Rust, particularly under a sink or near a dishwasher
  • Adjustment screws that are already wound to the end of their travel

If you are putting new doors on, it is a reasonable moment to replace tired hinges. You will be adjusting everything anyway.

What to tell us when you order

Whether your doors need boring, and if so to what positions, depends on the range. Ring 01206 616626 with the range you are looking at and your hinge measurements, and we will tell you what is possible for that range before you commit to anything.

Frequently asked questions

Can I use my old hinges on new doors?

Usually yes, provided the new doors are bored to take them and the cup size matches. The hinge does not care what the door is made of.

What if my new doors are a different thickness?

A small difference is absorbed by the hinge adjustment. A large one, for example going from 18mm to a chunky 22mm door, can change how the doors sit relative to each other and may need the mounting plates adjusting or changing.

How many hinges does a door need?

As a rough guide, two up to about 900mm tall, three up to about 1600mm, four above that. Heavy doors want an extra one regardless of height. Match what is on the door you are replacing unless it was clearly struggling.

My doors have never hung straight. Will new ones fix it?

Only if the doors were the problem. If the carcasses are out of square or the units have settled, new doors will hang exactly as badly. Check the carcass with a spirit level before you spend anything.