Everything about a door order depends on the measurements being right, because the doors are made to the sizes you give. This takes an hour for a whole kitchen and it is the hour that decides whether the job goes well.
What you need
- A steel tape measure, not a cloth one
- A pencil and paper, or a phone note
- A screwdriver, if you are taking doors off
Work in millimetres throughout. Kitchen doors are made in millimetres, and converting from inches at the end is how mistakes get in.
The rule that matters most
Measure the doors, not the gaps.
It is tempting to measure the opening in the carcass and work from that. Do not. The gap between doors is a consequence of the door size and how the hinges are adjusted, and every kitchen has slightly different gaps. Measuring the aperture gives you a number that is close enough to look right on paper and wrong enough to matter when the doors arrive.
If a door is missing or damaged beyond measuring, measure the one next to it on an identical unit, or measure the opening and ask us before you order.
Measuring a door
- Take the door off, or open it fully so you can get the tape flat against it.
- Measure the height first, from the top edge to the bottom edge, down the middle of the door rather than along an edge.
- Measure the width the same way, across the middle.
- Round to the nearest millimetre. Do not round to the nearest five or ten.
- Write it down as height by width, in that order, and keep that order for every door.
Height first, then width, is the convention the trade uses and the one our size lists follow. Swapping the two is the single most common ordering error there is, and on a tall narrow door it is an expensive one.
Measuring drawer fronts
Drawer fronts are measured exactly the same way, height then width. The thing to watch is that a bank of drawers often has fronts of two or three different heights, and they can be close enough to look identical. Measure every one.
Keeping track of which door is which
By the time you have measured a whole kitchen you will have twenty odd sets of numbers and no memory of which is which. Two habits fix it.
Number the doors. A small piece of masking tape on the back of each one, numbered, and the same number against the measurement on your list. If you take the doors off, the number is also how you know what goes back where.
Sketch the kitchen. A rough plan of each wall with boxes for the units, numbered to match. It does not need to be to scale. It needs to let you point at a number and know which door it is.
Note which way each door opens
For each door, write down whether the hinges are on the left or the right as you face it. Note which doors are a pair opening from the middle, and note any door that is handed, such as a corner unit door.
Some door styles look the same whichever way round they go. Others do not, particularly anything with a grain direction or a feature on one side. Getting the handing on your list means you cannot get it wrong later.
Common mistakes
- Measuring the gap instead of the door. Covered above, and worth repeating.
- Assuming identical units have identical doors. They often do not, by a millimetre or two.
- Writing width first on some doors and height first on others. Pick one order and never deviate.
- Forgetting the drawer fronts. They are half the order in a drawer heavy kitchen.
- Measuring over a handle or a raised moulding. Keep the tape flat on the face of the door.
- Not counting the end panels. They are not doors, but they are part of the order.
Before you order
Go round the kitchen once more with your list and check each number against the door it belongs to. A second pass takes ten minutes and catches almost everything.
If a size on your list does not match any standard size, say so when you order rather than rounding it to the nearest one that does. Ring 01206 616626 and we will tell you what the options are for that range.
Frequently asked questions
Should I measure with the doors on or off?
Off is more accurate, because you can lay the door flat and get the tape square to it. On is quicker and fine if you can hold the tape flat against the face. If you take them off, number them first.
What if my doors are not square?
Older doors can distort slightly. Measure the height at both edges and the width at the top and bottom. If the two readings differ, measure again at the middle and use that, and mention it when you order.
Do I need to measure the carcass at all?
Not for the doors. It is worth noting the carcass depth if you are ordering end panels, because the panel has to cover the unit plus the door thickness.
My kitchen has a mix of door sizes that look random. Is that normal?
Yes. Fitted kitchens are built to fit a room, and the units at the end of a run are often made to whatever width was left. Measure them all and do not assume.